Monel K500 is a precipitation-hardenable Nickel-copper alloy that combines the excellent corrosion resistance characteristic of Monel 400 with the added advantage of greater strength and hardness. These amplified properties, strength and hardness, are obtained by adding aluminum and titanium to the nickel-copper base and by a thermal processing used to effect precipitation, typically called age hardening or aging. When in the age-hardened condition, Monel K-500 has a greater tendency toward stress-corrosion cracking in some environments than Monel 400. Alloy K-500 has approximately three times the yield strength and double the tensile strength when compared with alloy 400. Plus, it can be further strengthened by cold working prior to precipitation hardening. The strength of this nickel steel alloy is maintained to 1200° F but stays ductile and tough down to temperatures of 400° F. Its melting range is 2400-2460° F.
|Monel K500 Price||Origin|| Price in INR
| Price in USD
|Price in Euro
|Monel K500 Price in India||Indian||Rs 1600/-||$24||€20|
|Monel K500 Price in Japan||Japanese||Rs 1790/-||$27||€23|
|Monel K500 Price in UK / Europe||European||Rs 1900/-||$28||€24|
|Monel K500 Price in USA||USA||Rs 2000/-||$30||€25|
Click here for complete (products, grade & size wise)
K500 Monel Alloy Chemical Composition
|63.0 min||0.25 max||2.3 – 3.15||1.5 max||0.5 max||05 – 2||27.0 – 33.0||0.010 max||0.35 – 0.85||–|
Monel Alloy K500 Mechanical Properties
|Density||Melting Point||Yield Strength (0.2%Offset)||Tensile Strength||Elongation|
|8.44 g/cm3||1350 °C (2460 °F)||Psi – 1,15,000 , MPa – 790||Psi – 1,60,000 , MPa – 1100||20 %|
1350 °C (2460 °F)
MONEL K500 is a age-hardenable Nickel-Copper alloy has high strength corrosion fatigue and erosion resistance. Monel K500 UNS N05500 products are a nickel-copper alloy, precipitation hardenable through additions of aluminum and titanium. Alloy K500 has the excellent corrosion resistant characteristics and enhanced strength and hardness after precipitation.It can be further strengthened by cold working before the precipitation hardening.
This nickel alloy is spark resistant and non-magnetic to -200° F. However, it is possible to develop a magnetic layer on the surface of the material during processing. Aluminum and copper may be selectively oxidized during heating, leaving a magnetic nickel rich film on the outside. Pickling orbright dipping in acid can remove this magnetic film and restore the non-magnetic properties.
Corrosion Resistant Monel K-500
The corrosion resistance of alloy K-500 is substantially equivalent to that of alloy 400 except that when in the age-hardened condition, nickel alloy K-500 has a greater tendency toward stress-corrosion cracking in some environments. Monel K-500 has been found to be resistant to a sour-gas environment. The combination of very low corrosion rates in high-velocity sear water and high strength make alloy K-500 particularly suitable for shafts of centrifugal pumps in marine service. In stagnant or slow-moving sea water, fouling may occur followed by pitting but this pitting slows down after a fairly rapid initial attack.
Chemical Composition, %
|63.0-70.0||Remainder||2.30-3.15||.35-.85||.25 max||1.5 max||2.0 max||.01 max||.50 max|
Applications of Monel K-500 :
Fabrication with Monel K-500 :
Monel K-500 is readily fabricated by standard commercial procedures.
Welding alloy K-500 is best accomplished by the gas-tungsten-arc welding process. It is recommended that Monel K-500 be annealed when it is welded and that any weldments be stress relieved prior to aging.
Heavy machining of this alloy is best accomplished when the material is in the annealed condition or hot-worked and quenched condition. Age-hardened material however can be finish-machined to close tolerances and fine finishes. Therefore, the recommended practice is to machine slightly oversize, age-harden, then finish to size. During aging, a slight permanent contraction takes place, but little warpage occurs because of the low temperatures and slow cooling rates involved.
Mechanical Properties :
Typical Room Temperature Tensile Properties of Annealed Material
|Product Form||Condition||Tensile (ksi)||.2% Yield (ksi)||Elongation %||Hardness|
|Rod & Bar||Hot-Finished/Aged||140-190||100-150||30-20||27-38 HRC|
|Rod & Bar||Hot Finished/Annealed||90-110||40-60||45-25||75-90 HRB|
|Rod & Bar||Hot Finished/Annealed/Aged||130-165||85-120||35-20||24-35 HRC|
|Rod & Bar||Cold-Drawn/Aged||135-185||95-160||30-15||25-41 HRC|
|Rod & Bar||Cold-Drawn/Annealed/Aged||130-190||85-120||30-20||24-35 HRC|
|Sheet||Cold-Rolled/Annealed||90-105||40-65||45-25||85 HRB Max|
Available forms are :